HRMW-510 T6

 

HRMW-510 T6

581 kVA Generator set Rental

Powered by: MTU
Alternator: STAMFORD

 

Three phase | 60 Hz | Diesel | TIER II

 

 

  • Engine Specifications 1.800 r.p.m.
  • Rated Output: 493kW prp ; 543kW standby
  • Manufacturer: MTU
  • Model: 10V1600G20S
  • Engine Type: 4-stroke diesel
  • Injection Type: Direct
  • Aspiration Type: Turbocharged and after-cooled
  • Number of cylinders and arrangement: 10V
  • Bore and Stroke: 122 x 150 mm
  • Displacement: 17,5 L
  • Cooling System: Coolant
  • Lube Oil Specifications: S10 W40
  • Compression Ratio: 17,5
  • Fuel Consumption ESP: 123,94 l/h
  • Fuel Consumption 100% PRP: 114,08 l/h
  • Fuel Consumption 75 % PRP: 90,02 l/h
  • Fuel Consumption 50 % PRP: 66,85 l/h
  • Fuel Consumption 25 % PRP: 36,39 l/h
  • Lube oil consumption with full load: 0,5 % of fuel consumption
  • Total oil capacity including tubes, filters 60,5 L
  • Total coolant capacity: 94 L
  • Governor Type Electrical
  • Air Filter Type Dry
  • Inner diameter exhaust pipe: 106 mm
  • Diesel engine
  • 4-stroke cycle
  • 24V electrical system
  • Water separator filter (visible level)
  • Dry air filter
  • Radiator with pusher fan
  • Radiator water level sensor
  • HTW sender
  • LOP sender
  • Electronic governor
  • Hot parts protection
  • Moving parts protection
  • - GENERATOR.
  • Poles: 4
  • Connection type (standard): Star - Parallel
  • Mounting type: S-1 14"
  • Insulation: H class
  • Enclosure (according IEC-34-5): IP23
  • Exciter system: Self-excited, brushless
  • Voltage regulator: A.V.R. (Electronic)
  • Bracket type: Single bearing
  • Coupling system: Flexible disc
  • Coating type: Standard (Vacuum impregnation)
  • - SOUNDPROOFED VERSION.
  • Steel chassis
  • Anti-leakage chassis, predisposed to retain liquids (retention tray)
  • High capacity fuel tank, with contention base and easy external filling
  • Manhole for fuel tank cleaning and drainage
  • Manhole for chassis cleaning
  • Oversized chassis to protect the bodywork
  • Slide carriage and brackets for transportation with forklift
  • Tilting cap in the exhaust
  • Manhole to fill the radiator
  • Pre-installation or niche to house the quick connection hydraulic fittings for fuel transfer
  • Anti-vibration shock absorbers
  • Chassis with integrated fuel tank
  • Fuel level gauge
  • Bodywork made from high quality steel plate
  • High mechanical strength
  • Low noise emissions level
  • Soundproofing provided by high-density volcanic rock wool
  • Epoxy polyester powder coating
  • Full access for maintenance (water, oil and filters, no need to remove the canopy)
  • Reinforced lifting hooks for crane hoisting
  • Steel residential silencer -35db(A) attenuation.
  • Oil sump extraction kit
  • External filling of the fuel tank with safety key
  • Emergency stop button (double emergency stop protection: Interior on the panel + Exterior on the bodywork)
  • Mechanized for power cable output
  • Door with window to visualize control panel, alarms and measurements
  • Pressure locks
  • IP Protection according to ISO 8528-13:2016
  • 3 way valve for external fuel supply (available in 1/2" and 3/8" fittings) (Optional)
  • Fuel transfer pump (Optional)
  • - ELECTRICAL SYSTEM.
  • 3-pole thermal magnetic circuit breaker
  • M5 control panel with electronic CEM7 control unit and switched emergency stop
  • Power panel with built-in circuit breaker plates
  • Safety relay in output terminal board (thermal magnetic trip and alarm in control unit)
  • Battery Switch
  • Adjustable earth leakage protection (time & sensitivity) standard in M5 and AS5, with thermal magnetic protection
  • Battery charger alternator with ground connection
  • Starter battery/ies installed (cables and bracket included)
  • Ground connection electrical installation with connection ready for ground spike (not supplied)
  • - EXHAUST SYSTEM.
  • Maximum exhaust temperature: 461 ºC
  • Exhaust Gas Flow: 102,6 m3/min
  • Maximum allowed back pressure: 150 mbar
  • Exhaust Flange Size (external diameter): 160 mm
  • - NECESSARY AMOUNT OF AIR.
  • Intake air flow: 2124 m3/h
  • Cooling Air Flow: 12 m3/s
  • Alternator fan air flow: 1,312 m3/s
  • - STARTING SYSTEM.
  • Starting power: 8 kW
  • Starting power: 10,88 CV
  • Recommended battery: 75 x 2 Ah
  • Auxiliary Voltage: 24 Vdc
  • Starter current peak: 800 A
  • Nominal starter current: 250 A
  • - FUEL SYSTEM
  • Fuel Oil Specifications: Diesel
  • Fuel Tank: 2.090 L
  • - DIMENSIONS.
  • Length: 4.602 mm
  • Height: 2.809 mm
  • Width: 1.850 mm
  • Maximum shipping volume: 23,91 m3
  • Weight with liquids in radiator and sump: 6.625 kg
  • Fuel tank capacity: 2.090 L
  • Autonomy: 23 Hours
  • Sound pressure level: 79 ± 2,4 dB(A)@7m
Engine
Oil sump extraction kit 70
Electrical Equipment
Water jacket heater M555
Fuel Feeding System
3 way valve fuel filling
Electric fuel transfer pump
Water separator filter with alarm
CEx Optionals
Telesignal
Kit CAN / LAN
Repetitive display: Remote Screen
Alarm Indicator Panel RAM7
Kit CAN/RS-485
Kit MODBUS TCP/IP
Kit CAN Profibus
Kit CAN/SNMP
Fleet Manager Module - C2CLOUD
C2CLOUD - 3G/GRPS and GPS
Kit CAN/LAN HG
Thermal Magnetic Protection
Change from 3P to 4P for 1600A
Extra to change to motorized circuit breaker 1600A
Advantage Version
Advantage Version Rental MTU
Fuel tank Leakage
Bund leak detector
Deepsea
Change of CEx for DSE7310
Change of CEx for DSE7320 controller

Power


kVA

581
 
638
Prime power  (460 - 700)
Stand by  (507 - 772)

kW

465
 
510
Prime power  (368 - 560)
Stand by  (405 - 617)
 

Sound level

 dB
 Distance (m)

 
 

dimensions


 
dimensions
Long (A)
460,20
Width (B)
185
High (C)
280,90
 

Weight


 
Weight
Weight with liquid in radiator and carter

6.625
 

Fuel capacity


 
 
2.090